chichi的分享天空

【CHICHI ETUTOR@ARM/MIPS/PPC】FILE SYSTEM _ guide to deploy ubuntu / Kbuntu on to ARM platform (S5pv210)

Here I wont give the real "steps" of how to install ubuntu onto ARM platform, instead, I will show the process of "how I tried to install ubuntu onto ARM platform which is "tiger board" that I always used"

before you starting doing anything below, make sure you that your system is bootable from uboot to any kind filesystem (even the simplest one)

and what we did here is download the ububtu filesystem from official, qemu it, install anything we need, and NFS this file system ,and copy the file system to the flash/usb/SD card .

1. download "armhf raring ubuntu filessytem" in my laptop :

//Take a while for 20~30 minutes to download it.

//after download and qemu this filesystem , you will enter this ubuntu filesystem

sudo qemu-debootstrap --arch armhf raring ubuntu_arm_raring_armhf http://old-releases.ubuntu.com/ubuntu

//now I "qemu" the arm platform and enter the filesystem in my X86 laptop , and configure it for further usage in ARM platform , the first one is setting the right repository address

root@ubuntu:/# echo "deb [arch=armhf] http://old-releases.ubuntu.com/ubuntu raring main restricted universe" > /etc/apt/sources.list

apt-get update

//download the wireless tools you will need it to install anything when the filesystem is trasfered to ARM platform.

apt-get install wireless-tools

//add the filesystem a new user "lawrence" and password

sudo chroot ubuntu_arm_raring_armhf useradd -m lawrence

sudo chroot ubuntu_arm_raring_armhf passwd lawrence

//change the name "ubuntu_arm_raring_armhf" and "root_mkfs", easier to operate.

mv ubuntu_arm_raring_armhf root_mkfs

4. need to be root and change the passwd

lawrence@node1:~$ sudo chroot root_mkfs su

root@node1:/# passwd

5. ifconfig wlan0 up

5-2 iwconfig wlan0 essid 'lawrence4'

5-3 dhcpcd wlan0

5-4 ping -I wlan0 168.95.1.1 //try to connect outside

--------destination host unreachable

5-4-1 change the gateway

route // show the route

route del default gw 192.168.0.0 eth0 //del the original gateway in eth0

route add default gw 192.168.1.1 wlan0 //change to wireless AP gw htc 192.168.1.1

5-4-2 try again ok

ping 168.95.1.1

//do these still in my laptop with qemu

apt-get install --no-install-recommemds ubuntu-desktop //would take 2-3hours

//do these still in my laptop with qemu

apt-get install gnome-session-fallback //ok the ubuntu screen is shown.

//NFS boot setting in "uboot" , set nfs_boot set bootargs noinitrd root=/dev/nfs nfsroot=192.168.10.59:/home/lawrence/Downloads/LARRY_S5PV210/day6_20130920/root_mkfs,proto=tcp,nfsvers=3 ip=192.168.10.20::192.168.10.1:255.255.255.0:hello.com.tw:eth0:off console=ttySAC0 mem=512M

// add ," getty -L -n console 115200 vt100" , to send message to UART1 , to /etc/rc.local to automatically enter UART login

>>>>>>>>>>then you should see the message like this >>>>>>>>

U-Boot 1.3.4 (Mar 29 2012 - 16:23:09) for SMDKV210

CPU: S5PV210@1000MHz(OK)

APLL = 1000MHz, HclkMsys = 200MHz, PclkMsys = 100MHz

MPLL = 667MHz, EPLL = 80MHz

HclkDsys = 166MHz, PclkDsys = 83MHz

HclkPsys = 133MHz, PclkPsys = 66MHz

SCLKA2M = 200MHz

Serial = CLKUART

Board: SMDKV210

DRAM: 1 GB

Flash: 8 MB

SD/MMC: 29476MB

NAND: 256 MB

In: serial

Out: serial

Err: serial

checking mode for fastboot ...

Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x600000, size 0x400000

Main area read (32 blocks):

4194304 bytes read: OK

Boot with zImage

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

[ 0.000000] Initializing cgroup subsys cpu

[ 0.000000] Linux version 2.6.35.7 (lawrence@ubuntu) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #19 PREEMPT M5

[ 0.000000] CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f

[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache

[ 0.000000] Machine: SMDKV210

[ 0.000000] Ignoring unrecognised tag 0x41001099

[ 0.000000] Memory policy: ECC disabled, Data cache writeback

[ 0.000000] Truncating RAM at 40000000-5fffffff to -53ffffff (vmalloc region overlap).

[ 0.000000] CPU S5PV210/S5PC110 (id 0x43110220)

[ 0.000000] S5PV210: PLL settings, A=1000000000, M=667000000, E=80000000 V=54000000

[ 0.000000] S5PV210: ARMCLK=1000000000, HCLKM=200000000, HCLKD=166750000

[ 0.000000] HCLKP=133400000, PCLKM=100000000, PCLKD=83375000, PCLKP=66700000

[ 0.000000] sclk_dmc: source is sclk_a2m (0), rate is 200000000

[ 0.000000] sclk_onenand: sourc 0.000000] sclk: source is mout_mpll (6), rate is 66700000

[ 0.000000] sclk: source is mout_mpll (6), rate is 66700000

[ 0.000000] sclk_mixer: source is sclk_dac (0), rate is 54000000

[ 0.000000] sclk_spdif: source is sclk_audio (0), rate is 24000000

[ 0.000000] sclk_fic: source is ext_xtal (0), rate is 24000000

[ 0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000

[ 0.000000] sclk_cam0: source is ext_xtal (0), rate is 24000000

[ 0.000000] sclk_cam1: source is ext_xtal (0), rate is 24000000

[ 0.0xtal (0), rate is 24000000

[ 0.000000] sclk_mmc: source is mout_mpll (6), rate is 47642857

[ 0.000000] sclk_mmc: source is mout_epll (7), rate is 80000000

[ 0.000000] sclk_mmc: source is mout_mpll (6), rate is 47642857

[ 0.000000] sclk_mmc: source is mout_epl 0.000000] sclk_mfc: source is sclk_a2m (0), rate is 200000000

[ 0.000000] sclk_g2d: source is sclk_a2m (0), rate is 200000000

[ 0.000000] sclk: source is sclk_a2m (0), rate is 200000000

[ 0.000000] sclk_csis: source is ext_xtal (0), rate is 24000000

[ 0.000000] sclk_spi: source is ext_xtal (0), rate is 24000000

[ 0.000000] sclk_spi: sour 0.000000] sclk_pwi: source is ext_xtal (0), rate is 24000000

[ 0.000000] sclk_pwm: source is ext_xtal (0), rate is 24000000

[ 0.000000] sclk_mdnie: source is ext_xtal (0), rate is 24000000

[ 0.000000] sclk_mdnie_pwm: source is ext_xtal (0), rate is 24000000

[ 0.000000] s5pv210: 37748736 bytes system memory reserved for mfc at 0x20eef000

[ 0. reserved for mfc at 0x40000000

[ 0.000000] s5pv210: 25165824 bytes system memory reserved for fimc0 at 0x42400000

[ 0.000000] s5pv210: 10137600 bytes system memory reserved for fimc1 at 0x43c00000

[ 0.000000] s5pv210: 25165824 bytes system memory reserved for fimc2 at 0x445ab000

[ 0.000000] s5pv210: 8388608 bytes system memory reserved for jpeg at 0x45dab000

[ 0.000000] s5pv210: 6144000 bytes system memory reserved for fimd at 0x465ab000

[ 0.000000] s5pv210: 3072000 bytes system memory reserved for texstream at 0x46b87000

[ 0.000000] s5pv210: 3379200 bytes system memory reserved for pmem_gpu1 at 0x46e75000

[ 0.000000] s5pv210: 8388608 bytes system memory reserved for g2d at 0x471ae000

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 211328

[ 0.000000] Kernel command line: noinitrd root=/dev/nfs nfsroot=192.168.10.59:/home/lawrence/Downloads/LARRY_S5PV210/e

[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

[ 0.000000] Memory: 512M56k/674456k available, 177512k reserved, 0K highmem

[ 0.000000] Virtual kernel memory layout:

[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)

[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)

[ 0.000000] DMA : 0xff000000 - 0xffe00000 ( 14 MB)

[ 0.000000] vmalloc : 0xf4800000 - 0xfc000000 ( 120 MB)

[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)

[ 0.000000] .init : 0xc0008000 - 0xc002c000 ( 144 kB)

[ 0.000000] .text : 0xc002c000 - 0xc05df000 (5836 kB)

[ 0.000000] .data : 0xc05e0000 - 0xc0626120 ( 281 kB)

[ 0.000000] SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

[ 0.000000] Hierarchical RCU implementation.

[ 0.000000] RCU-based detection of stalled CPUs is disabled.

[ 0.000000] Verbose stalled-CPUs detection is disabled.

[ 0.000000] NR_IRQS:393

[ 0.000000] VIC @fd000000: id 0x00041192, vendor 0x41

[ 0.000000] VIC @fd010000: id 0x00041192, vendor 0x41

[ 0.000000] VIC @fd020000: id 0x00041192, vendor 0x41

[ 0.000000] VIC @fd030000: id 0x00041192, vendor 0x41

[ 0.000000] Console: colour dummy device 80x30

[ 0.000000] console [ttySAC0] enabled

rating delay loop... 996.14 BogoMIPS (lpj=2490368)

[ 0.145000] pid_max: default: 32768 minimum: 301

[ 0.145000] Mount-cache hash table entries: 512

[ 0.145000] Initializing cgroup subsys debug

[ 0.145000] Initializing cgroup subsys cpuacct

[ 0.145000] Initializing cgroup subsys freezer

[ 0.145000] CPU: Testing write buffer coherency: ok

[ 0.150000] devtmpfs: initialized

[ 0.155000] regulator: core version 0.5

[ 0.155000] regulator: dummy:

[ 0.160000] NET: Registered protocol family 16

[ 0.170000] pmstats at 00000000

[ 0.175000] smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857

[ 0.180000] smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857

[ 0.185000] smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857

[ 0.190000] smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857

[ 0.195000] S5PV210: Initializing architecture

[ 0.200000] s3c24xx-pwm s3c24xx-pwm.0: tin at 66700000, tdiv at 66700000, tin=divclk, base 0

[ 0.205000] s3c24xx-pwm s3c24xx-pwm.1: tin at 66700000, tdiv at 66700000, tin=divclk, base 8

[ 0.210000] s3c24xx-pwm s3c24xx-pwm.2: tin at 22233333, tdiv at 22233333, tin=divclk, base 12

[ 0.215000] s3c24xx-pwm s3c24xx-pwm.3: tin at 22233333, tdiv at 22233333, tin=divclk, base 16

[ 0.220000] regulator: pd_audio_supply: 5000 mV normal

[ 0.230000] regulator: pd_cam_supply: 5000 mV normal

[ 0.235000] regulator: pd_tv_supply: 5000 mV normal

[ 0.240000] regulator: pd_lcd_supply: 5000 mV normal

[ 0.245000] regulator: pd_g3d_supply: 5000 mV normal

[ 0.250000] regulator: pd_mfc_supply: 5000 mV normal

[ 0.255000] bio: create slab <bio-0> at 0

[ 0.255000] SCSI subsystem initialized

[ 0.260000] usbcore: registered new interface driver usbfs

[ 0.265000] usbcore: registered new interface driver hub

[ 0.270000] usbcore: registered new device driver usb

[ 0.275000] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter

[ 0.280000] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter

[ 0.285000] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter

[ 0.290000] Advanced Linux Sound Architecture Driver Version 1.0.23.

[ 0.295000] cfg80211: Calling CRDA to update world regulatory domain

[ 0.305000] NET: Registered protocol family 2

[ 0.305000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)

[ 0.310000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)

[ 0.315000] TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)

[ 0.320000] TCP: Hash tables configured (established 131072 bind 65536)

[ 0.325000] TCP reno registered

[ 0.330000] UDP hash table entries: 512 (order: 2, 24576 bytes)

[ 0.335000] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)

[ 0.340000] NET: Registered protocol family 1

[ 0.345000] RPC: Registered udp transport module.

[ 0.350000] RPC: Registered tcp transport module.

[ 0.355000] RPC: Registered tcp NFSv4.1 backchannel transport module.

[ 0.365000] PMU: registered new PMU device of type 0

[ 0.375000] smdkc110-rtc smdkc110-rtc: rtc core: registered s3c as rtc0

[ 0.385000] cpuidle: phy_regs_save:0x53fff000

[ 0.390000] Loaded driver for PL330 DMAC-0 s3c-pl330

[ 0.395000] DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32

[ 0.400000] Loaded driver for PL330 DMAC-1 s3c-pl330

[ 0.405000] DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32

[ 0.410000] Loaded driver for PL330 DMAC-2 s3c-pl330

[ 0.415000] DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32

[ 0.425000] ashmem: initialized

[ 0.425000] msgmni has been set to 1317

[ 0.430000] alg: No test for stdrng (krng)

[ 0.430000] io scheduler noop registered

[ 0.430000] io scheduler deadline registered

[ 0.435000] io scheduler cfq registered (default)

[ 0.440000] s3cfb s3cfb: [fb2] dma: 0000000, size: 0x005dc000

[ 0.455000] Console: switching to colour frame buffer device 100x30

[ 0.460000] FIMD src sclk = 166750000

[ 0.580000] s3cfb s3cfb: registered successfully

[ 0.655000] PA FB = 0x465AB000, bits per pixel = 32

[ 0.655000] screen width=800 height=480 va=0xe65ab000 pa=0x465ab000

[ 0.655000] xres_virtual = 800, yres_virtual = 1920, xoffset = 0, yoffset = 0

[ 0.655000] fb_size=6144000

[ 0.655000] Back frameBuffer[0].VAddr=e6722000 PAddr=46722000 size=1536000

[ 0.660000] Back frameBuffer[1].VAddr=e6899000 PAddr=46899000 size=1536000

[ 0.665000] Back frameBuffer[2].VAddr=e6a10000 PAddr=46a10000 size=1536000

[ 0.670000] s5pv210-uart.0: s3c2410_serial0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10

[ 0.680000] s5pv210-uart.1: s3c2410_serial1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10

[ 0.685000] s5pv210-uart.2: s3c2410_serial2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10

[ 0.690000] s5pv210-uart.3: s3c2410_serial3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10

[ 0.700000] brd: module loaded

[ 0.705000] loop: module loaded

[ 0.710000] S3C NAND Driver is using hardware ECC.

[ 0.715000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)

[ 0.720000] Creating 7 MTD partitions on "s5pv210-nand":

[ 0.725000] 0x0000000c0000-0x000000100000 : "misc"

[ 0.735000] 0x000000100000-0x000000600000 : "recovery"

[ 0.740000] 0x000000600000-0x000000b00000 : "kernel"

[ 0.745000] 0x000000b00000-0x000000e00000 : "ramdisk"

[ 0.750000] 0x000000e00000-0x000007c00000 : "system"

[ 0.770000] 0x000007c00000-0x00000cc00000 : "cache"

[ 0.790000] 0x00000cc00000-0x000010000000 : "userdata"

[ 0.800000] smsc911x: Driver version 2008-10-21.

[ 0.800000] smsc911x: Driver version A2008-10-21.

[ 0.800000] smsc911x: Driver version AA 2008-10-21.

[ 0.800000] smsc911x: Driver version AAA 2008-10-21.

[ 0.800000] LAN base phy in probe: 0xA8000000

[ 0.800000] LAN base virt in probe: 0xF4892000

[ 0.805000] smsc911x-mdio: probed

[ 0.805000] eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)

[ 0.810000] net eth0: MAC Address: 00:09:c0:ff:ec:48

[ 0.815000] usbcore: registered new interface driver rt73usb

[ 0.820000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[ 0.825000] s5p-ehci s5p-ehci: s5pv210 EHCI

[ 0.830000] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1

[ 0.835000] s5p-ehci s5p-ehci: irq 87, io mem 0xec200000

[ 0.850000] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00

[ 0.850000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

[ 0.850000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[ 0.855000] usb usb1: Product: s5pv210 EHCI

[ 0.855000] usb usb1: Manufacturer: Linux 2.6.35.7 ehci_hcd

[ 0.860000] usb usb1: SerialNumber: s5pv210

[ 0.865000] hub 1-0:1.0: USB hub found

[ 0.870000] hub 1-0:1.0: 1 port detected

[ 0.875000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

[ 0.880000] s5p-ohci s5p-ohci: s5pv210 OHCI

[ 0.885000] s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2

[ 0.890000] s5p-ohci s5p-ohci: irq 87, io mem 0xec300000

[ 0.950000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001

[ 0.950000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[ 0.950000] usb usb2: Product: s5pv210 OHCI

[ 0.950000] usb usb2: Manufacturer: Linux 2.6.35.7 ohci_hcd

[ 0.955000] usb usb2: SerialNumber: s5pv210

[ 0.960000] hub 2-0:1.0: USB hub found

[ 0.960000] hub 2-0:1.0: 1 port detected

[ 0.965000] Initializing USB Mass Storage driver...

[ 0.970000] usbcore: registered new interface driver usb-storage

[ 0.975000] USB Mass Storage support registered.

[ 0.980000] s3c-udc : version 15 March 2009 (DMA Mode)

[ 0.985000] android init

[ 0.985000] android_probe pdata: c05ed758

[ 0.990000] android_bind

[ 0.995000] android_usb gadget: android_usb ready

[ 1.020000] f_acm init

[ 1.020000] android_register_function acm

[ 1.020000] f_adb init

[ 1.020000] android_register_function adb

[ 1.020000] f_mass_storage init

[ 1.020000] fsg_probe pdev: c05ec6d8, pdata: c05ed77c

[ 1.020000] android_register_function usb_mass_storage

[ 1.025000] f_mtp init

[ 1.025000] android_register_function mtp

[ 1.030000] f_rndis init

[ 1.030000] android_register_function rndis

[ 1.035000] rndis_function_bind_config MAC: 02:02:45:46:4F:48

[ 1.040000] android_usb gadget: using random self ethernet address

[ 1.045000] android_usb gadget: using random host ethernet address

[ 1.050000] usb0: MAC ea:e4:0e:09:76:0c

[ 1.055000] usb0: HOST MAC 56:cd:1b:bc:c0:f6

[ 1.060000] android_usb gadget: Mass Storage Function, version: 2009/09/11

[ 1.065000] android_usb gadget: Number of LUNs=1

[ 1.070000] lun0: LUN: removable file: (no medium)

[ 1.075000] adb_bind_config

[ 1.075000] mtp_bind_config

[ 1.080000] mice: PS/2 mouse device common for all mice

[ 1.085000] bma150 2-0038: bma150 found

[ 1.090000] bma150 2-0038: al_version=2, ml_version=1

[ 1.125000] input: bma150 as /devices/virtual/input/input0

[ 1.125000] i2c /dev entries driver

[ 1.125000] Linux video capture interface: v2.00

[ 1.125000] s3c-csis: Samsung MIPI-CSI2 driver probed successfully

[ 1.130000]

[ 1.140000] JPEG driver for S5PV210

[ 1.145000] i2c i2c-1: attached s5p_ddc into i2c adapter successfully

[ 1.160000] s3c_bat_init

[ 1.160000] sec-fake-battery sec-fake-battery: s3c_bat_probe

[ 1.165000] device-mapper: uevent: version 1.0.3

[ 1.175000] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com

[ 1.180000] cpuidle: using governor ladder

[ 1.185000] sdhci: Secure Digital Host Controller Interface driver

[ 1.190000] sdhci: Copyright(c) Pierre Ossman

[ 1.195000] s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133400000 Hz)

[ 1.200000] s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133400000 Hz)

[ 1.205000] s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (47642857 Hz)

[ 1.210000] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA

[ 1.215000] s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133400000 Hz)

[ 1.220000] s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133400000 Hz)

[ 1.225000] s3c-sdhci s3c-sdhci.1: clock source 2: sclk_mmc (47642857 Hz)

[ 1.230000] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA

[ 1.235000] s3c-sdhci s3c-sdhci.2: clock source 0: hsmmc (133400000 Hz)

[ 1.240000] s3c-sdhci s3c-sdhci.2: clock source 1: hsmmc (133400000 Hz)

[ 1.245000] s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (47642857 Hz)

[ 1.250000] mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA

[ 1.255000] s3c-sdhci s3c-sdhci.3: clock source 0: hsmmc (133400000 Hz)

[ 1.260000] s3c-sdhci s3c-sdhci.3: clock source 1: hsmmc (133400000 Hz)

[ 1.265000] s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (47642857 Hz)

[ 1.270000] mmc3: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA

[ 1.275000] usb 1-1: new high speed USB device using s5p-ehci and address 2

[ 1.280000] usbcore: registered new interface driver usbhid

[ 1.285000] usbhid: USB HID core driver

[ 1.290000] logger: created 64K log 'log_main'

[ 1.295000] logger: created 256K log 'log_events'

[ 1.300000] logger: created 64K log 'log_radio'

[ 1.300000] logger: created 64K log 'log_system'

[ 1.310000] asoc: AC97 HiFi <-> s3c-ac97 mapping ok

[ 1.365000] mmc0: new high speed SDHC card at address aaaa

[ 1.365000] mmcblk0: mmc0:aaaa SL32G 28.7 GiB

[ 1.365000] mmcblk0: p1 p2 p3

[ 1.420000] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608

[ 1.420000] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0

[ 1.420000] usb 1-1: Product: USB2.0 Hub

[ 1.420000] hub 1-1:1.0: USB hub found

[ 1.420000] hub 1-1:1.0: 4 ports detected

[ 1.695000] usb 1-1.3: new high speed USB device using s5p-ehci and address 3

[ 1.945000] usb 1-1.3: New USB device found, idVendor=148f, idProduct=2573

[ 1.945000] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0

[ 1.945000] usb 1-1.3: Product: 802.11 bg WLAN

[ 1.945000] usb 1-1.3: Manufacturer: Ralink

[ 2.280000] usb 1-1.4: new full speed USB device using s5p-ehci and address 4

[ 2.335000] AC97: Unable to activate!

[ 2.370000] usb 1-1.4: New USB device found, idVendor=046d, idProduct=c52e

[ 2.370000] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0

[ 2.370000] usb 1-1.4: Product: USB Receiver

[ 2.370000] usb 1-1.4: Manufacturer: Logitech

[ 2.375000] input: Logitech USB Receiver as /devices/platform/s5p-ehci/usb1/1-1/1-1.4/1-1.4:1.0/input/input1

[ 2.380000] generic-usb 0003:046D:C52E.0001: input: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-s5pv210-1.40

[ 2.390000] input: Logitech USB Receiver as /devices/platform/s5p-ehci/usb1/1-1/1-1.4/1-1.4:1.1/input/input2

[ 2.395000] generic-usb 0003:046D:C52E.0002: input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-s5pv210-1.4/in1

[ 3.335000] AC97: Unable to read!

[ 3.375000] ALSA device list:

[ 3.375000] #0: SMDK (WM9713)

[ 3.375000] GACT probability NOT on

[ 3.375000] Mirror/redirect action on

[ 3.375000] u32 classifier

[ 3.375000] Actions configured

[ 3.375000] TCP cubic registered

[ 3.375000] NET: Registered protocol family 17

[ 3.380000] NET: Registered protocol family 15

[ 3.385000] lib80211: common routines for IEEE802.11 drivers

[ 3.390000] ThumbEE CPU extension supported.

[ 3.395000] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2

[ 3.405000] regulator_init_complete: disabling pd_mfc_supply

[ 3.410000] regulator_init_complete: disabling pd_tv_supply

[ 3.415000] regulator_init_complete: disabling pd_cam_supply

[ 3.420000] smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling

[ 3.425000] smdkc110-rtc smdkc110-rtc: hctosys: invalid date/time

[ 3.435000] FIMC0 registered successfully

[ 3.435000] FIMC1 registered successfully

[ 3.440000] FIMC2 registered successfully

[ 3.450000] s5p-tvout s5p-tvout: hpd status is cable inserted

[ 3.975000] net eth0: SMSC911x/921x identified at 0xf4892000, IRQ: 41

[ 4.980000] IP-Config: Complete:

[ 4.980000] device=eth0, addr=192.168.10.20, mask=255.255.255.0, gw=192.168.10.1,

[ 4.980000] host=hello, domain=, nis-domain=com.tw,

[ 4.980000] bootserver=255.255.255.255, rootserver=192.168.10.59, rootpath=

[ 4.980000] DBUG_PORT must not use AFC!

[ 4.985000] Looking up port of RPC 100003/3 on 192.168.10.59

[ 6.995000] Looking up port of RPC 100005/3 on 192.168.10.59

[ 7.020000] VFS: Mounted root (nfs filesystem) on device 0:14.

[ 7.025000] devtmpfs: mounted

[ 7.025000] Freeing init memory: 144K

[ 15.330000] init: ureadahead main process (60) terminated with status 5

[ 16.620000] init: mounted-proc main process (67) terminated with status 1

[ 35.420000] readl S5P_VP_ENABLE for VP_POWER_DOWN_RDY fail

[ 35.420000] s5p_vlayer_stop::s5p_vp_stop() fail

ubuntu login:

Password:

ubuntu login: root

Password: 2udiogul

Last login: Thu Jan 1 00:02:08 UTC 1970 on console

Welcome to Ubuntu 13.04 (GNU/Linux 2.6.35.7 armv7l)

* Documentation: https://help.ubuntu.com/

Your Ubuntu release is not supported anymore.

For upgrade information, please visit:

http://www.ubuntu.com/releaseendoflife

New release '13.10' available.

Run 'do-release-upgrade' to upgrade to it.

-bash: no job control in this shell

root@ubuntu:~#

<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<

//and in the screen, the ubuntu welcome and login should be displayed like this

//you can copy "root_mkfs" files to the sd card partition and do boot without NFS but with SD card

,here is the uboot parameter for boot file system from SD card

//bootargs, sd_boot=set bootargs noinitrd root=/dev/mmcblk0p1 rootfstype=ext3 mem=512M console=ttySAC0

//you can even install other version OS

apt-get install kubuntu-desktop

chichi的分享天空

[琪琪雜貨舖]

2016年2月14日星期日

【CHICHI ETUTOR@ARM/MIPS/PPC】FILE SYSTEM _ guide to deploy ubuntu / Kbuntu on to ARM platform (S5pv210)

0 意見:

張貼留言

[琪琪雜貨舖]

[琪琪雜貨舖]

2016年2月14日 星期日

【CHICHI ETUTOR@ARM/MIPS/PPC】FILE SYSTEM _ guide to deploy ubuntu / Kbuntu on to ARM platform (S5pv210)

0 意見:

張貼留言

[琪琪雜貨舖]

2016年2月14日星期日